Mr-Glass Construction in Hillsborough, CA

Mr-Glass Construction in Hillsborough, CA | Ashford Contractors

We install, repair, and replace Mr-Glass shower enclosures and glass systems across Hillsborough, CA, as a trusted General Contractor in Hillsborough. The work here runs different than anywhere else on the Peninsula because Hillsborough’s older custom homes rarely have square walls, and the town’s architecture review and tree-protection rules often force a glass project to be re-measured after framing actually goes in, not from the drawing. That’s the thing most glass contractors learn the hard way in Hillsborough. We learned it fifteen years ago, and our whole approach is built around it. Call (877) 752-3868 for a free estimate on Mr-Glass framing, templating, hinge repair, or panel replacement.

Call (877) 752-3868

Why Hillsborough Residents Choose Us for Mr-Glass Service

We’re not a Mr-Glass dealer. We’re an independent general contractor that installs and services Mr-Glass in Burlingame and across the Peninsula, so our estimators work directly from the manufacturer’s fabrication specs rather than a dealer network. That matters when a frameless unit is templated wrong or a hinge fails: we diagnose and re-fit it in the field instead of pushing a whole new enclosure. For Hillsborough homeowners, that independence means the fix we recommend is the fix you actually need, not the one with the highest markup.

Our owner, Glen Mossier, grew up in Foster City’s Marlin Cove and trained in construction technology at Skyline College. He’s spent two decades on Mr-Glass service in San Mateo County remodels, and he’ll tell you the same thing he tells our crews: build it right the first time, and you won’t be rebuilding it in ten years. That philosophy shows up in every Mr-Glass template we take, every hinge we reset, and every caulk line we lay along a Hillsborough curb.

We keep OEM Mr-Glass hinges, pivots, sweeps, and seals stocked for the enclosure lines most common in Hillsborough homes, which means faster turnaround without waiting on a distributor shipment.

Common Mr-Glass Construction Problems We Solve in Hillsborough

• Out-of-plumb templates on mid-century bathrooms. Hillsborough’s older custom homes rarely have square walls. A field measure taken on a racked wall from a 1950s or 1960s bath yields an enclosure that won’t close cleanly on the hinge side. We template to the actual framed opening, not the drawing, and adjust pivot placement accordingly.
• Hinge and pivot fatigue on heavy frameless doors. Heavier 3/8-inch frameless doors on sloped-ceiling or non-standard opening baths sag at the pivot over time, causing sweep-seal drag and water escape. Hillsborough has no shortage of sloped ceilings and custom door openings, so we see this failure mode constantly and repair it with OEM pivots rated for the actual panel weight.
• Seal and caulk failure at the curb. Winter rains plus slab or curb movement on clay-heavy Peninsula soils break the silicone line, letting water wick under the track. We see this across Hillsborough’s wooded lots, where soil expands and contracts with the rainy season. We re-caulk with a slope-correct bead so runoff actually sheds back to the drain.
• Coating and hard-water haze on fixed panels. Unsealed or worn factory coatings on Mr-Glass panels in high-mineral water leave mineral etching that looks like permanent clouding. Once the coating is compromised, the glass itself gets attacked. We’ll replace the panel when that happens and talk through coating options that hold up to Peninsula water chemistry.
• Re-scoped openings after tree-protection review. Root-zone protection rules in Hillsborough can limit where a plumbing wall or curb moves, which changes the rough-in dimensions after architectural review is already done. Glass templated before that re-scope is wrong the day it’s cut. We template after the actual rough-in, every time.

Mr-Glass Service in Hillsborough: What Local Conditions Mean for Your Equipment

Here’s the thing nobody outside Hillsborough understands: the town’s design-review and tree-protection rules mean a bath or glass project can clear architectural review and still be re-scoped at framing, because root-zone protection on wooded lots often limits where a plumbing wall or curb can move. A homeowner gets approval for a curb shift, then the arborist comes back and flags a mature oak, and suddenly the curb stays put or moves two inches the other way. Now the opening width is different, the door swing is different, and any glass templated from the original drawing no longer fits.

We’ve pulled off Mr-Glass repair in Highlands-Baywood Park and Hillsborough enclosures where the glass was cut to a plan that didn’t survive contact with the actual rough-in. On a mid-century ranch off Crystal Springs Road, our crew took over a bathroom where the original Mr-Glass frameless hinged enclosure had been templated to the drawing rather than the framed opening, and the door dragged on a racked wall. We re-measured against the plumb line, reset the pivot hinge, switched to a 3/8-inch fixed panel with an OEM sweep, and re-caulked the curb with a slope-correct bead so winter runoff shed back to the drain instead of under the track. That’s the difference between glass that works in Hillsborough and glass that works on paper.

Mr-Glass Models & Products We Service in Hillsborough

We install and service the Mr-Glass frameless hinged shower enclosure in the Gen series, the semi-frameless sliding tub-shower enclosure, the Neo-Angle corner shower enclosure, and custom-cut Mr-Glass glass panels and mirrors. For enclosures we service, we source OEM hinges, pivots, sweeps, and seals so the fit and load rating stay correct. We’ll substitute quality aftermarket hardware only when an OEM part is discontinued and no equivalent remains available through the manufacturer’s parts channel. Replacing seals, hinges, or a single glass panel is almost always the right call before considering a full enclosure replacement, and that stance is what keeps our Hillsborough repair bills lower than a full re-enclosure would run. For our full brand line and parts approach, see our Mr-Glass sales & service page.

Mr-Glass Service Pricing in Hillsborough

FAQs – Mr-Glass Construction in Hillsborough

Service Areas Near Hillsborough

We run Mr-Glass glass and enclosure work across the Peninsula from our San Mateo County base. Beyond Hillsborough, our crews regularly work in Foster City, Redwood Shores, Belmont, San Mateo, and Highlands-Baywood Park, so we know the housing stock and soil conditions in every one of them. See our Hillsborough service area page for our full local coverage, our Mr-Glass service in Emerald Lake Hills page, or our Mr-Glass service in Millbrae page for more.

Book Your Mr-Glass Service in Hillsborough Today

If your Mr-Glass enclosure is dragging, leaking, or just not closing the way it should, call us. We’ll template it right, fix what’s actually broken, and stand behind the work. Estimates are free, and we’ll tell you straight if a repair is the right call instead of a replacement. Call (877) 752-3868.

Written by Glen Mossier, Owner at Ashford Contractors, serving Hillsborough across the Peninsula.